W-BOX technical function: 1: The box has 8 isolated DMX512 outputs and 8 WS281x LED lights with SPI output, which can not only control DMX512 devices, but also directly control LED lights; 2: Box has a 150M, 2.4G Wifi; 3: The box has 2 network ports, and the box has its own switch and router. Different protocols do not need to be switched, they will be processed at the same time and automatically resolved; 12: The box can capture any light show written by a physical console with network transmission or simulation software through the network, and save it as an offline DMX file dedicated to the box, which is convenient for box playback or external device call and trigger. 13: The box supports many professional software, most of which have been cracked. Supported software list all software and console with Artnet and sACN output are supported. Note: Most free software does not have multi-universe output so need use professional software.
Support the output of all universe, has been cracked, using hahan protocol. The demo software has free universe output, supports 64 universe, can crack 200 universe at most, using Artnet or hahan protocol. Supports the output of all universe, using Artnet or sACN protocol, can find cracked versions on the Internet, we cannot crack this software. Support the output of all universe, the software can output up to 70 universe, has been cracked, using hahan protocol.Support the output of all universe, the software can output up to 40 universe, has been cracked, using hahan protocol. Support the output of all universe, the software can output up to 50 universe, has been cracked, using hahan protocol. Support the output of all universe, the software has a maximum of 8 universe, has been cracked, using hahan protocol. Support the output of all universe, the software can output up to 256 universe, has been cracked, using hahan protocol. Supports the output of all universe, the software has a maximum of 256 universe, has cracked 2.14f3.6f version, using Artnet or sACN protocol. Support the output of all universe, the software has a maximum of 4 universe, has been cracked, using hahan protocol. Support the output of all universe, the software has a maximum of 6 universe, has been cracked, using hahan protocol. Official demo software with 4 universe output, uncracked, using Artnet protocol. Free software, using Artnet or sACN protocol.
There are many cracked VJ software on the Internet, using Artnet or sACN protocol. Free software, using Artnet or sACN protocol, can run macOS, windows, linux system. If you have any good software, you can send it to me, let me try.DC In: 7.5V25V / 2A1A. 8 port of 250K standard DMX512 output, with optical signal and electrical signal isolation, each channel has an exclusive 16bit domain address, and each channel can independently set any port from 0 to 65535. Hardware with 3 DC-DC power isolation, 8 signal optical isolation. 8 universe, 800K single-line output, timing compatible with WS281x chips. 2 output lines, each line outputs 4 universe, also compatible Madrix patch fixture with dmx512 mode.
2.4G / 150Mb , can be set to open and close freely. Start peak:800ma , working:120ma. 2 port 10M/100Mb adaptive lan interface, programmable. LAN1 and SD card/PWM multiplexing, LAN1 and SD/PWM cannot be used at the same time, choose 1 of 2. Host, can connect to most USB devices, special devices need us to write drivers.DC: 500ma output, with PTC protection. TF card, support any capacity. 1 hard reset RST button (if pressed the box will reset and restart), 1 multi-function WPS button. If box Wifi is turned off, press and hold WPS for 5 seconds, wifi will be turned on, if you continue to hold for more than 20 seconds, the box will be restored to the factory settings. 5 LED lights, 2 green lights, 2 yellow lights, 1 red light.
Different combinations of flashing, on and off have different definitions. Have command line tools, easy script programming. 1 receiving, 1 transmitting (IO port mode).
Can support more than 99% of infrared remote controls on the market, the box does not have a remote control, the remote control needs to be set (learned) before it can be used. GPIO multiplexing, with command line tools. 3 port: UART0 for Linux, UART1/UART2 for general equipment. UART1/2 multiplexed with GPIO, TTL level, UART1 is 3.3V, UART2 is 5V, Not RS232, connect to RS232 will burn the main chip!
Can reuse other function pins to release more GPIO. One 3.3V/ one 5V. 5V with PTC protection, limited to 500ma, 3.3V without protection, if the output power plus the total power of the box is greater than 8W, it will protect, So, please try not to use 3.3V to power external devices, because 3.3V consumes a lot of power.
Attention please: If you do not have professional knowledge, please do not easily connect items 1015, because these pins are directly connected through the main CPU chip. The core working voltage of the CPU is 1.2V/1.8V, and the maximum voltage that the pins can withstand is 3.3V, if the external signal or power supply greater than 3.3V is connected by mistake, the CPU will be burned, If the CPU is burned, the box will basically be scrapped. Yellow 2, 4 will flash alternately once, the red 5 light will light up first and then flash.Red light is on or flashes occasionally (normal working state). Long light indicates that the network cable is normal, flashing means have network data. Flashing means that the access network cable is normal, have network data. Connect wifi and have Wifi data will flash. Please press the Rest button or unplug the power to reset once.
Do not turn off the box power during the upgrade, the upgrade will take 3 minutes. The item "W-Box DMX Controller DMX-USB. Com for DMX Stage Light Madrix GrandMa2 lightjockey" is in sale since Friday, January 22, 2021.
This item is in the category "Musical Instruments & Gear\Stage Lighting & Effects\Stage Lighting Dimmers". The seller is "knlblackstore" and is located in Zhongshan.
This item can be shipped worldwide.